Request quoteCall now
Blaugelb Triotherm+ Precasings – Thermal Installation in the Insulation LayerPerimeter Insulation

nZEB Systems

Blaugelb Triotherm+ Precasings – Thermal Installation in the Insulation Layer

High-density EPS profiles that bring the window into the facade insulation layer and reduce the installation thermal bridge. System certified by the Passive House Institute.

Technical specifications

MaterialHigh-density EPS, grey
Thermal conductivity λD0.040 W/mK (EN 12667)
Profile widths70 / 100 / 120 / 160 mm
Section and length85 mm high, 1175 mm bars
Load transferover 200 kg
Compressive stress (10%)≥ 2,500 kPa
Water absorption (28 days)≤ 1.5% vol.
Reaction to fireclass E (EN 13501-1)
Fixingbonded and mechanically fixed to the masonry, dovetail joints
Recyclability100%, free of HCFC, HFC, HBCD

Certified performance

CertificationPassive House Institute, mounting system (2017)
Effective system conductivity0.042 W/mK, including screw losses
Sealingthree-level tapes, per the RAL guideline
Dimensional stabilityvery high, including outdoor weathering
Window fixingreversible, no pre-drilling

Key advantages

  • The window is fitted in the facade insulation layer: the frame leaves the cold zone of the wall and the joint thermal bridge drops sharply compared with fitting inside the masonry opening
  • System certified by the Passive House Institute, with an effective conductivity of 0.042 W/mK that already includes the screw losses
  • It carries the weight of the window: over 200 kg of load transfer and compressive stress of at least 2,500 kPa, with no metal brackets to create a thermal bridge
  • It gives the tapes a flat, stable surface, so the three-level sealing (outer tape, foam, inner vapour barrier) is done properly
  • It does not degrade with moisture: water absorption below 1.5% in 28 days, no mould and no rot
  • It works with PVC, aluminium and timber windows; the profiles join with dovetails to any length, and the window can be removed again during renovation

Blaugelb Triotherm+ precasings are high-density EPS profiles (λD = 0.040 W/mK) fixed to the masonry, in the facade insulation layer, before the window goes in. The window is then mounted on the profile rather than inside the masonry opening: the frame sits in the insulation plane, and the joint thermal bridge, which with conventional fitting brings condensation and mould to the reveal and the corners, drops sharply. The profiles carry over 200 kg and withstand compressive stress of at least 2,500 kPa, so metal brackets are no longer needed. The Blaugelb Triotherm+ system is certified by the Passive House Institute as a mounting system, with an effective conductivity of 0.042 W/mK that also covers the screw losses. The sealing tapes go onto the profile according to the RAL installation guideline: pre-compressed tape outside, foam in the middle and a vapour barrier inside. The nZEB rules do not require precasings by name, but thermal bridges count in the building energy calculation, and a precasing is the recommended solution whenever the window is fitted in the facade insulation. Neofort BIZ installs Blaugelb Triotherm+ precasings in Bucharest and Ilfov; the extra cost is 25–50 EUR per linear metre of perimeter for PVC windows and 30–60 EUR for aluminium windows, excluding VAT.

Frequently asked questions

The precasing is a high-density EPS profile fixed to the masonry in the facade insulation layer. The window is mounted on it rather than straight into the masonry opening, so the frame leaves the cold zone of the wall and the joint thermal bridge drops sharply.

The profile has λD = 0.040 W/mK, measured to EN 12667. The Passive House Institute certified the complete system with an effective conductivity of 0.042 W/mK, which also includes the screw losses.

No. The nZEB rules do not require precasings by name, but thermal bridges count in the building energy calculation. A precasing is the recommended solution whenever the window is fitted in the facade insulation, in nZEB and passive houses alike.

One profile carries over 200 kg and withstands compressive stress of at least 2,500 kPa. It is bonded and mechanically fixed to the masonry, and the profiles join with dovetails to any length. It suits PVC, aluminium and timber windows.

Installation with precasings costs an extra 25–50 EUR per linear metre for PVC and 30–60 EUR for aluminium, excluding VAT. The material absorbs less than 1.5% water in 28 days, does not go mouldy and is 100% recyclable. The precasings are made by Blaugelb.

Request quote for

Blaugelb Triotherm+ Precasings – Thermal Installation in the Insulation Layer

Consultants available Mon–Fri, 10:00–18:00

Request quoteCall now +40 752 443 435