# Blaugelb Triotherm+ precasings: the window in the insulation

> Blaugelb Triotherm+ precasings move the window into the facade insulation layer and reduce the joint thermal bridge. What they are, how they are fitted, what they cost and when they pay off.

- Article page: https://www.neofort-biz.ro/en/blog/blaugelb-triotherm-precasing-installation-nzeb
- Published: February 22, 2026 (2026-02-22)
- Category: Installation
- Reading time: 7 min read
- Author: Mihai Dănălache, Neofort BIZ

---

## The problem nobody mentions at the sale

You can buy the best [Salamander PVC profile](https://www.neofort-biz.ro/en/pvc-windows), bluEvolution 92, with triple glazing and a Warm Edge spacer. If the window is fitted the conventional way, inside the masonry opening with the frame against the wall, **some of the heat still escapes around the edges**, and the performance measured in the laboratory no longer shows up in full in the house.

Why? Because of **perimeter thermal bridges** — the areas around the window where indoor heat passes to the outside through the wall material faster than through the wall or the window itself.

**Blaugelb Triotherm+** precasings were designed for exactly this problem. The law does not require them by name, but in a house that has to reach the **[nZEB standard](https://www.neofort-biz.ro/en/nzeb-systems)** every thermal bridge counts in the calculation, and a precasing is the cleanest solution when the facade insulation is thick.

---

## What are Blaugelb Triotherm+ precasings?

Blaugelb is a German brand of the Meesenburg group, specialising in installation and sealing systems for windows and doors. **Triotherm+** is its pre-wall installation system, which places the window in front of the masonry, in the facade insulation layer.

A Blaugelb Triotherm+ precasing is a **high-density EPS profile** (λ = 0.040 W/mK) that is bonded and mechanically fixed to the masonry around the opening before the window goes in. Its role:

1. **Moves the window into the insulation plane**, away from the cold zone of the wall
2. **Carries the weight of the window** — over 200 kg per profile, with no metal brackets
3. **Creates a flat fitting plane** on which the sealing tapes bond properly
4. **Stays stable** in damp conditions: it absorbs less than 1.5% water in 28 days and does not go mouldy

### Components of the complete system

- **Triotherm+ profiles** — in widths of 70, 100, 120 and 160 mm, joined with dovetails
- **Pre-compressed tape** — outer seal against rain and wind (Neofort BIZ uses Soudal tapes)
- **Vapour barrier tape** — on the inside, against condensation in the joint
- **Elastic polyurethane foam** — the insulation in the middle of the joint
- **Adhesive and anchors** for fixing the profiles to the masonry

---

## How it works thermally

With conventional fitting, the frame sits in the masonry opening and the facade insulation stops at the edge of the opening. Masonry conducts heat far better than polystyrene, so a cold path forms around the window. In winter, with 20°C inside and −10°C outside, the inner surface of the reveal and the corners cools down.

The result: **condensation and, over time, mould on the inner perimeter of the window**, plus heat losses that do not appear on the window datasheet.

With a Blaugelb Triotherm+ precasing, the window sits in the insulation layer. The EPS profile has a conductivity close to that of the facade insulation, so the cold path is interrupted. The inner surface temperature stays closer to room temperature and **the risk of perimeter condensation drops sharply**.

---

## What role does the precasing play in nZEB?

Romania's Law no. 372/2005 on the energy performance of buildings, as amended, transposes European Directive 2010/31/EU. Since the end of 2020, new buildings must be nZEB: primary energy use below the threshold set for the climate zone and building type, with at least 30% of the energy from renewable sources.

The energy calculation, carried out under the **Mc 001-2022** methodology, also includes the linear thermal bridges (Ψ values) around the windows. The law does not name precasings, but a large thermal bridge at every window adds up and can push the building over the threshold.

**In practice:** when the window is fitted in the facade insulation, a precasing is the recommended solution. The Blaugelb Triotherm+ system is certified by the Passive House Institute as a mounting system, with an effective conductivity of 0.042 W/mK that also includes the screw losses.

---

## Correct installation — step by step

**1. Preparing the opening**
Check that the masonry around the opening is flat. Surfaces must be clean, dry and free of dust so the adhesive grips.

**2. Fitting the profiles**
The profiles are bonded to the masonry and mechanically fixed all around the opening. They are joined with dovetails and aligned carefully, because their plane becomes the plane of the window.

**3. Outer pre-compressed tape**
It is applied to the frame **before** the window is installed. After fitting it expands and closes the joint against rain and wind, while still letting vapour escape.

**4. Fitting the window**
The window is placed on the profiles and fixed with screws straight into the EPS, with no pre-drilling. The remaining joint is filled with **elastic PU foam** — the middle insulation layer.

**5. Inner vapour tape**
It is bonded continuously on the inside, between the frame and the masonry. It stops indoor vapour from entering the joint and condensing there.

**6. Finishing**
The facade insulation is taken over the profiles and over part of the frame. This closes the last cold section around the window.

---

## What it costs and when it pays off

Installation with Blaugelb Triotherm+ precasings costs an extra **25–50 EUR per linear metre of perimeter** for PVC windows and **30–60 EUR** for aluminium windows, excluding VAT. A 1.2 × 1.4 m window has a perimeter of 5.2 m, so the difference is about 130–260 EUR for PVC. In a house with 12 such windows, the extra cost comes to roughly 1,500–3,100 EUR.

It pays off above all in new houses with thick facade insulation and in nZEB or passive houses, where every thermal bridge counts. In a simple renovation with the window fitted in the existing opening, a RAL installation with three-level tapes is usually enough.

---

## Conclusion

At Neofort BIZ, installation with Blaugelb Triotherm+ precasings is an option we recommend for nZEB houses and houses with thick insulation. Measurements are taken after the contract is signed, and we send the quote within 48 hours of receiving the dimensions.

## Frequently Asked Questions

### What is a Blaugelb Triotherm+ precasing made of?

A Blaugelb Triotherm+ precasing is a high-density EPS profile with λ = 0.040 W/mK, bonded and mechanically fixed to the masonry in the facade insulation layer. It carries over 200 kg, resists moisture and is 100% recyclable.

### Is installation with precasings mandatory in an nZEB house?

No. The law does not require precasings, but the thermal bridges around the windows count in the energy calculation under Mc 001-2022. When the window is fitted in the facade insulation, a precasing is the recommended solution because it sharply reduces the joint thermal bridge.

### What does the complete installation system consist of?

The complete system has the Triotherm+ profiles, the pre-compressed tape outside (Neofort BIZ uses Soudal tapes), the vapour barrier tape inside, the elastic PU foam in the middle of the joint, and the adhesive and anchors that fix the profiles.

### What happens if the window is fitted without a precasing?

The window stays in the masonry opening and the wall conducts heat around its edge. There are heat losses that the window datasheet does not show and, in winter, condensation or mould on the reveal and in the corners. A RAL installation with three-level tapes reduces the problem but does not move the window into the insulation.

### How much does installation with Blaugelb precasings cost?

The extra cost is 25–50 EUR per linear metre of perimeter for PVC windows and 30–60 EUR for aluminium windows, excluding VAT. For a 1.2 × 1.4 m window, the difference is about 130–260 EUR for PVC.

---

Neofort BIZ installs Blaugelb Triotherm+ precasings and windows for nZEB houses in Bucharest and Ilfov. See [the nZEB systems](https://www.neofort-biz.ro/en/nzeb-systems) we offer or [request a quote](https://www.neofort-biz.ro/en/contact). See also [the complete guide to nZEB house windows](https://www.neofort-biz.ro/en/blog/windows-nzeb-house-romania-complete-guide-2026). Useful pages: [Blaugelb Triotherm+ precasings](https://www.neofort-biz.ro/en/nzeb-systems/blaugelb-triotherm-plus-precasings) and [the complete nZEB systems guide](https://www.neofort-biz.ro/en/nzeb-systems/complete-guide).

---

Quote and contact: https://www.neofort-biz.ro/en/contact · oferte@neofort-biz.ro · +40 752 443 435 · Neofort BIZ SRL, București
